![]() | ||
Metropower Portal | ||
| ||
![]() Moderators: Jump to page : 1 2 3 Now viewing page 3 [25 messages per page] | |
Technical Area-> Technical | Message format |
minimad01![]() |
| ||
New user Posts: 5 | how would i go about fitting a 1.4 or 1.6 into a metro an running bike carbs ? | ||
cliffordliam![]() |
| ||
![]() Green machine! Posts: 585 ![]() ![]() ![]() ![]() Location: Bromley, Kent | Don't know if anyone can help, changing my 1.4 gta carb and going to mpi, I have fitted everything except the bloody fuel lines can some one tell me best way to get them in? | ||
AdrianSi![]() |
| ||
![]() Expert Posts: 8490 ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() Location: Midlands | With the front subframe it will be a bit of a struggle, you may have to install them one by one to feed them past the subframe. Exhaust off, heat shield off and gearlinkages out of the way will also make this easier. | ||
cliffordliam![]() |
| ||
![]() Green machine! Posts: 585 ![]() ![]() ![]() ![]() Location: Bromley, Kent | Oh okay mate I also have the front arb still there should I remove | ||
Pietaster![]() |
| ||
![]() Admin Posts: 1576 ![]() ![]() ![]() ![]() ![]() Location: Burnley, Lancs | Defo take the arb off, I had to do this when I coverted mine and you can get them in without having to take anything else off it's just a case of wrestling them in. You should only have to fit one pipe? Just fit the injection feed pipe, the carb feed pipe is the same as the injection return pipe. | ||
minispeedstar![]() |
| ||
Regular Posts: 252 ![]() ![]() ![]() ![]() | This may have already have been answered here, but i'd be greatfull of some advise please. I've just bought a 1994 MPI GTI Metro and i'd like to fit a 1.8VVC what exactly do i need to do or change to fit one please? will a vvc run on the MPI metro ecu for example? Cheers guys! | ||
111Sli![]() |
| ||
![]() Transport Guru MP Moderator Posts: 4947 ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() Location: Bromley, Kent | Check the first post of the thread on page 1! also, get some pics up of your GTI. Rare cars now! | ||
minispeedstar![]() |
| ||
Regular Posts: 252 ![]() ![]() ![]() ![]() | 111Sli - 8/3/2012 7:53 PM Check the first post of the thread on page 1! also, get some pics up of your GTI. Rare cars now! Have posted some pics now, I have read the first post but am still unsure about the ecu etc...? so can i use the GTI ecu for a VVC?.. | ||
R100_vvc![]() |
| ||
![]() Expert Posts: 2029 ![]() ![]() Location: sittingbourne, kent | No you will need to use a vvc ecu, you can get loom conversions so its plug and play if you hate wiring. PM AdrianSi very well recomended for loom conversions Edited by R100_vvc 8/3/2012 10:07 PM | ||
Alex_B![]() |
| ||
Member Posts: 38 ![]() Location: Hull | Hi All, I have managed to pick up a 2001 MGF VVC as a donor for a 1995 R100 1.4 8v Spi Car, the Spi is very poorly as the engine is tired and old. Reading this forum I can see what bits are used to do a VVC engine conversion but can I take the MGF gearbox (drive shafts etc.) across too and what bits of the MGF suspension can I use? I'm assuming that I can use the engine wiring loom and the ECU(reprogrammed to get rid of the BCU link) off the MGF in the R100? I think it is a 143bhp car; I know that I will need a 52mm TB and a better air induction system to take this up to 160bhp, but what else is needed. Does the Engine management system need changing. Thanks for any guidance in advance. Alex_B. | ||
pickford![]() |
| ||
![]() Extreme Veteran Posts: 586 ![]() ![]() ![]() ![]() Location: brighouse just shy huddersfield | had a read thru here I have a complete mems 3 1800 solid cam mgzr if it's on an r65 would I just need to source a clutch engine loom and fuel pump? do I still need an mpI loom if I get a plug and play mems 3 loom? | ||
MetroGaz![]() |
| ||
Veteran Posts: 335 ![]() ![]() ![]() ![]() Location: York, tis Cold Up North! | I suggest you contact Adrian Barnsley and discuss what you have and what you still need and he will advise correctly. Done many looms etc for people on here. MG | ||
Jump to page : 1 2 3 Now viewing page 3 [25 messages per page] |
Printer friendly version E-mail a link to this thread Jump to forum : |
(Delete all cookies set by this site) | |
Running MegaBBS ASP Forum Software v2.0 © 2003 PD9 Software | |